Amigas run on Motorola 68000 Processors.

PiStorm

Custom Chips

• What worked
  • Transcend PCMCIA → CF adapter
  • SanDisk 512MB
• What didn't
  • Verbatim 4GB
• You can't use an Amiga FFS or similar card in the PCMCIA slot. It has to be FAT16 or FAT32.

If running in a MiSTer FPGA Emulation System, you need to set up PPP networking on both the MiSTer and in the network stack config. Follow the PPP networking instructions there, then come back here.

• Have MiamiDX use the PPP IP address and set up everything else so it makes sense for your network.
• If the connection starts acting weird, reset the UART and reconnect in MiamiDX

An Arduino-based Ethernet adapter for am Amiga's parallel port. It's not fast but it works.

• https://lallafa.de/blog/amiga-projects/plipbox/

I ended up getting this one: https://amiga68k.com/?product=plipbox-deluxe-commodore

You may need to enable NOBURST on certain configurations, like on PiStorm.

• Cabletron RoamAbout 802.11b card
• prism2.driver
  • Get the prism2v2 so you can get WPA2
  • WirelessManager runs in the background and handles the connection to the network, while MiamiDX does the TCP/IP stuff
• MiamiDX

• I needed to set up hostapd on a Raspberry Pi to create a slightly downgraded access point that bridged to the rest of my network.

  # hostapd.conf wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP

• Floppy writes in FS-UAE are cached via overlays
• The USB drive needs to be formatted fat16 and you need two files at the root of it
• My Gotek has two buttons. You use the two buttons to move back and forth between the mounted ADFs
  • Some Goteks I think have rotary encoders as well
• You can't put new ADFs into the rotation without a reboot

It's possible for the Gotek to eat the partition table on a USB drive. It should be recoverable if you use testdisk: https://www.tecmint.com/install-testdisk-data-recovery-tool-in-linux/

I have one of these: https://www.waveshare.com/wiki/0.91inch_OLED_Module

It plugs into the LED pins. When I got my Gotek it came with the display in a Gotek cutout box, so I'm assuming display-type = oled-128x32-narrow is stored in flash memory. More details:

• https://github.com/keirf/FlashFloppy/wiki/Hardware-Mods#oled-display
• https://github.com/keirf/FlashFloppy/wiki/FF.CFG-Configuration-File

Use AHI. You're probably using it with Paula anyway.

• http://aminet.net/package/driver/audio/m68k-amigaos-ahiusr
• http://aminet.net/package/driver/audio/AHI-Paula for a better Paula driver.

AmigaAMP is what you want.

• http://aminet.net/package/mus/play/AmigaAMP3-68k

Then, load this prefs in AHI config (http://www.amigaamp.de/Binaries/PaulaPrefs/ahi.prefs) and save it. Enjoy your streaming audio.

• Skins
  • It can use WinAMP skins. Here, use this one: https://skins.webamp.org/skin/99543ffaf75f2e6e99e8541605115d40/Sabrina_Amiga_ForeverAMP.wsz/
  • You can unzip a skin into its own folder in PROGDIR:Skins/ or install a decompressor library to handle .wsz files directly.